Description | DESCRIPTION
When lifting your truck, the stock upper arms become the limiting factor and hold back your suspensions performance. Our Camburg upper arms address these issues and more. Replacing the stock ball-joint with a larger 1.25 uni-ball bearing we’re able to gain wheel travel with a part that is considerably stronger and will last longer under extreme conditions. We build more caster and change the camber curve to correct geometry so the vehicle aligns correctly and improves driving characteristics and handling.
Using the latest CAD/CAM engineering software we design these arms to the strictest standards using our FARO laser scan arm to model the OEM parts and frames. Manufactured in-house, we have the tubes CNC laser cut and bent, then are MIG welded in precision fixtures before sending out to be sandblasted and powder-coated. Our in-house CNC machine shop makes all the machined parts including the uniball mis-alignment spacers from heat-treated stainless steel. We pride ourselves in producing the best parts available under our own roof and control.
- Increases usable wheel travel
- Corrects camber and caster
- Eliminates weak factory ball-joints
- Thicker .156″ wall round tubing
- Laser cut & CNC bent tubes MIG welded
- CAD/CAM engineered
- Polyurethane frame pivot bushings with grease-able zerk fittings
- FK 1.25″ PTFE-lined uniballs pre-installed
- Steel gray powder-coating
- All necessary hardware included and ready to install
- Made in the USA
- Designed for 1-3″ of lift
|
2008+ LC200, 2WD & 4WD, UCA (PAIR)
|
Computer designed upper a-arm uses a fabricated, Boxed Arm design for ultimate strength. It allows significantly more wheel travel over stock when paired with an extended length, bolt in, aftermarket shock and we've built more caster into all of our Upper arms to give your truck the on road stability needed anytime a truck is lifted from its factory ride height. We use Trophy Truck grade uniballs to replace the weak, stock ball joints, giving you maximum articulation and performance in the dirt with your 2WD or 4WD Silverado. These will also work great with your existing lift kit that most likely has maxed out the stock ball joint angle. | | Upper Control Arm
Getting the correct alignment is no longer a problem. Not only do these arms provide for better wheel alignment settings, they have been designed to include increased clearance between the arm and strut at full droop. These arms deliver up to 3 degree of caster along with extra camber, allowing for the optimum alignment settings for a 2" lifted vehicle.
FEATURES:
-
- Increased articulation, perfect for the off road environment
- Provides for camber and caster adjustment using an adjustable ball joint
- Increased clearance between spring and Control Arm at full articulation
- SuperPro Bushings
Vehicle Application:
- Adjustable up to 4 Degrees increase in Caster and + or - 2 Degrees Camber Adjustment
- Arms fitted with Uprated Ball Joints and SuperPro Bushes to reduce Arm movement
.
| Countless hours were spent designing and refining these arms to the point where they met our high standards. CAD designing and machining gave us the ability to bring some new design elements and features to the table. We CNC machine these from aerospace quality 6061 billet aluminum, then send them out to be bead blasted, Type II anodized gun metal gray and have our Camburg logo laser etched.
Like our tubular arms we use a larger FK 1.25” uniball that has a PTFE liner for increased strength and mis-alignment for maximum useable wheel travel. Made in the USA these are far superior to the cheaper and smaller imports other companies use. Adapting the uniball to the spindle/knuckle is done using model specific spacers that match the factory taper precisely. These are machined from heat-treated stainless steel and are a one piece design for increased strength. No drilling or modifications are needed. The 1.25” uniball gives us the ability to run a 12 point bolt with a low profile press-on uniball cap to resist the elements.
Using larger and stronger FK 7/8” chromoly heim joints allows for additional camber and caster adjustment if needed. Using a heim joint also eliminates flexing/deflection under hard use and braking with zero binding when in use. Using AN/Mil-spec hardware we have a single pinch bolt and secondary jam nut to insure the heim is secure with the rigors of off-road use.
- NEW V2 design
- Increases usable wheel travel
- Corrects camber and caster
- Eliminates weak factory ball-joints
- CNC machined 6061 billet aluminum
- CAD/CAM engineered
- FK 7/8″ heim joints for adjustable camber and caster
- FK 1.25″ PTFE-lined uniballs pre-installed
- Anodized and laser etched
- All necessary hardware included and ready to install
- Made in the USA
- Designed for 1-3″ of lift
- Compatible with King 3.0 and FOX 2.5 DSC coilovers
|
The Baja Kits Advantage:
- Billet Aluminum Machined in house on our CNC Mill
- CNC Top cap with O-ring keeps debris and water out of your uniball joint
- 3/4 Rod end inner pivots offer incredible strength over stock bushings and add open the door to custom caster/camber adjustment for custom or details setup applications
- 1" Hi angle Trophy Truck grade uniball replace the weak stock ball joints that fail under high angles and loads seen from normal offroad use
- Our CNC machined corrosion resistant misaligns have a tapered snout to adapt your stock upright/spindle with ease
- We've increased the caster angle that you lose when lifting a truck with stock arms to regain on road stability, handling and alignmentTechnical Specs:
Wheel Travel: Unlocks the potential for 2.5"+ more wheel travel when paired with king shocks
Track Width - Stock width
Lift - 0-3"
Product Requirements:
Shocks - Aftermarket Replacement 2.5
Tire Size 35" are recommended, 37's are possible but aggressive & May need to limit steering for proper clearance
Wheel Size - 17" rim with 4.5/4.75" max backspacing
|
Additional information |
Weight |
11 kg |
Dimensions |
38 × 37 × 18 cm |
|
Weight |
7 kg |
Dimensions |
40 × 31 × 16 cm |
| |
Weight |
9.3 kg |
Dimensions |
47 × 43 × 41 cm |
|
Weight |
9 kg |
Dimensions |
38 × 37 × 18 cm |
|
Weight |
7.1 kg |
Dimensions |
42 × 32 × 17 cm |
|
Reviews
There are no reviews yet.